Ford axle identification.

Ford Axle Code Chart .: Articles. I don't speak or write Spanish, this is all from on-line translations. Clutch, Transmission, Differential, Axle & Transfer Case - Axle ID's decoded - Front axle tag reads: 4 09 D7TA ZC 610010 4R Rear axle tag reads: 4 10 D7TA ACB 603883 11 Please help me correctly ID these. 77 F-250 4WD.1932-1934 the wishbones are bolted to the bottom of the axle housings about 8" from the ends. the tabs for the wishbones are welded on, but will not go all the way around the housing, just the bottom. the spring hangers are forged on to the axle tubes. on the 1932, the part where the torque tube bolts to the diff is round (most) it is more of a ...Ford Rear Axle Assembly Identification - Page 01: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WBG-E : Ford Truck '63-71 F100: 3.70: 9 in: NL: 28-WBG-F : Ford Truck '63-71 F100: 3.89: 9 in: NL: 28-WBG-H: …Ford Rear Axle Assembly Identification - Page 11: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S157B: Ford F250SD, F350SD Pickup ‘99: 4.10: 10.50: L--S157C: Excursion '00 Ford F250SD, F350SD Pickup ‘99-01: …Step 3. Locate the identification tags on the rear-end housing unit. According to the Dana/Spicer Corporations' "Roadranger" Illustrated Parts List, there are two identification tags, one located on the driver's side differential carrier and one on the passenger side of the axle housing. Both tags contain similar information, however, the axle ...

Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:

DANA 30. The Model 30, with a 7 1/8-inch-diameter ring gear, was the standard front differential in some 1972-75 CJ-5s and all 1975-and-later CJ-5s and CJ-7s. It is still used in the front of Cherokees and Comanches, and will probably appear in the front of the Grand Cherokee. R.G. Diameter 7.20". 10 Bolt 3/8 X 24 RH.

If it's your year's car and for a mustang and it matches whatever your door tag says is supposed to be back there, then more than likely it is original to the car. Unless you find a casting code somewhere though, there's no way to be 100% positive that it's original. Ford Rear Axle Information. 2003 V-6 - the usual bolt-ons.The Ford 3E axle code can have a significant impact on the performance and capabilities of a Ford vehicle. The 3E code represents specific gear ratios and differential types, which can influence factors such as towing capacity, acceleration, and fuel efficiency. By understanding the 3E axle code, drivers can make more informed …409 = Print Number (Model Number) B = Revision Identifier (Change in Design) 3L73: 3L73 = 3.73 Ratio. L = Limited Slip. Absence of L = Open Differential. A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3 (space)73. 102 denotes the ring gear size. 10.25 inches.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:

The Ford Sterling 10-1/2" Rear Full-Floating Axle was introduced in 1999 along with the new Super Duty F250 and F350. It shares some parts with the similar 10-1/4" Sterling Rear Axle which Ford used from 1985 to 1997 in the F250 and F350. The 10-1/2" Sterling is equipped with disc brakes (with the possible exception of some very early ...

4. Axle Code 27 - 3.31 Open Rear Axle. This code designates an open rear axle with a 3.31 axle ratio. It strikes a balance between fuel economy and performance, being commonly found on F150s equipped with smaller engines. 5. Axle Code K2 - 3.55 Electronic Locking Rear Axle w/ Torsen Differential.

The 1963 Ford body plate data decoder enables you to discover the vehicle's build information including paint color, body style and trim. FORD Body Plate IdentificationFord Rear Axle Assembly Identification - Page 04. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines. Additional Information. Ratio.FORD ID TAGS | GM RPO CODES | DANA SPICER BOM NUMBERS | VISUAL IDENTIFICATION. When repairing or upgrading differential parts, the first and most …Originally Posted by 85e150. See post 2. I guess I should ask @ford390gashog that question. Why he thinks it's a Meritor axle. With no locker, my only option to get unstuck would be to install individual rear braking. Funny, all the trucks I know of and owned in Europe had lockers. Must be the muddy terrain.Another sopt is a white sticker located in the doorjamb there is either a number or letter under axle. Conventional or "open" rear ends break down as follows: 8-2.73, Y-3.08, 5-3.27, F-3.45, 6-3.73. ... Mustang Club of America #82740, White Mustang Registry #362, NMRA, Fun Ford Weekend, Mustangs of Burlington M O OG Certified Technician For ...

Step 2 - Decode the VIN. Once the VIN is located, write it on a plain paper and begin decoding. For example, a typical VIN for a Ford truck can follow this format: 1FT-L-P62-W-4-X-H-128703. The number 1 …Ford Rear End Catalog: Hot to Select Axle & Measure the Companion Flange: Your Source for Classic / Late Model Auto Parts: INFO 404-767-3378 FAX 404-305-9437: CONTACT METRO: ... How to tell whether yours has a 28 or 31 spline axle. This method works for pre-1971 axles, after that a few 31 splines were produced with the concave oval in the ...What Are Ford Axle Codes? Definition of Ford Axle Codes. Axle codes are alphanumeric codes used by Ford to identify the specific differential installed in a …Table of axle codes for the Ford F-150. In the table below you can see a selection of two-character codes, simply read across to the left to find your axle ratio – 3.31, 3,55 3.73, 4.10 and 9.61 for the lightning. You can see that codes that are purely numeric (e.g. “19“) correspond to a Non-limited slip, and codes with a letter (e.g. “L6“) correspond …1973 - 1979 F-100 & Larger F-Series Trucks - axle identification - hey guys just got this truck for free its a late 78 or 79 f250 camper special 4x4 supercab the body is shot! but i want to find out the front axle it has king pins so im thinking it is a d60 let me know what ya think! Thanks!...mustange70. 4031 posts · Joined 2005. #8 · Nov 17, 2005. the pre superduty trucks used dana 80's (easy way to tell is if it has disc brakes its a dana 80) and all f-350/f-250 used the 10.25 from the mid eighties up to the superduties, then the superduties as far as i know the 250/350 all used the 10.5 and the 450 and up used the dana 135, but ...Early Bronco Front Axle Identification: Dana 30 vs Dana 44. The first generation Ford Bronco came with either a Dana 30 or Dana 44 front axle. The Dana 30 was used from 1966 to mid-year 1971. At this point in 1971, Ford made the switch to the beefier Dana 44 front end and continued this through 1977, the last year of the early Bronco.

Check the axle code on your door jamb. 99r is the code for the wide one I found written on another site. ... Ford Powerstroke Diesel Forum. 5.4M posts 267.7K members Since 2005 A forum community dedicated to Ford F-series owners and enthusiasts with a Power Stroke diesel engine. Come join the discussion about …Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

1994 Ford Mustang Axle Information & Ratios. Your Mustang will be equipped with a Vehicle certification label on the driver’s side door jam. This label will show your axle code under the “AX” slot. ... Axle identification: Ratio and Type: 8: 2.73 Axle Ratio – Conventional: M: 2.73 Axle Ratio – Limited slip: 7: 3.07 Axle Ratio ...Both the Super Duty Dana 50 (Bottom) and Dana 60 (Top) have 1.50-inch axle shafts, but on the Dana 50 the shafts are machined down to 1.30-inch at the differential. The Dana 50 is also fitted with 30-spline inners, whereas the Dana 60 gets 35 splines. Typically, the Dana 50 and Dana 60 were both equipped with 1350 pinion yokes under the Super Duty.In the Ford Explorer, some common axle codes include: 31 - 3.27 gear ratio with an open differential. V6 - 3.27 gear ratio with a limited-slip differential. 55 - 3.55 gear ratio with an open differential. C7 - 3.73 gear ratio with a conventional differential. L9 - 3.73 gear ratio with a limited-slip differential.Nov 27, 2017 · F-350 rear axle identify. I bought a rear axle with a broken ring gear for a project truck. In working on my F350 driver I needed to replace a rear caliper and found there was a right and left. I thought (scary things happen) and looked at my project rear axle and it does not have a right or left. The right caliper hangs on the rear and the ... Ford Rear Axle Assembly Identification - Page 16. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Ford Rear Axle Assembly Identification - Page 16: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V012-A: Ford Pass., Mercury 86-91: 2.73: 8.8: NL: 28-V012-B:F66 = F600 4x4 gas. E = 361 4V XD FT gas V8. V = Kentucky Truck Plant. 080631 = 1977 numerical series, December 1976 production. F600 4x4 came in 3 GVWR levels--. F650 = 17,200 lbs. F660 = 21,700 lbs. F661 = 24,000 lbs. These are the model numbers that would appear on the warranty plate, and maybe on a build sheet if you find one.

1973 - 1979 F-100 & Larger F-Series Trucks - Axle Identification - Hi, I have a '78 F-150, 4 x 2, was a 351 M now a 460. The rear axle is coded 15 J on the door. ... See here Ford Rear Axle Assembly Identification - Page 04 - FORDification.com . Reply Like #7 03-26-2013, 09:54 PM ...

Ford Rear Axle Assembly Identification - Page 09: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. 79-82 Lincoln & Town Car 80-81 Lincoln & Town Car '82 Mercury 80-82: 2.73: 8.5: NL: 28-WGY-A2: Ford Pass. 82-83 Lincoln & Town Car '82-83 Mercury 82-83: ...

Early 1977 and older Ford F250 (sometimes) Ford D60. The easy ID for these is that they use a low pinion arrangement, while all Ford D60's '77.5 and newer are high pinion (van conversions are the rare exception). Kingpin style knuckles. 31-1/2" spring pad spacing-You want to tread really lightly with these axles.Ford Rear Axle Assembly Identification - Page 08: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WFG-A: Ford Pass., Mercury '70-74: 2.75: 9 in: L: 28-WFG-A: Ford Pass., Mercury 70-74:Feb 19, 2016 · It’s worth noting that rear axles can sometimes be positively identified by a casting number and date stamped on the differential cover or axle tube. However, road debris, dirt, grime, and general age can obscure these numbers. Fortunately, you can tell a lot about a rear axle by its shape and number of bolts on the differential housing. 92 F-250 front axle ID. I've got a 92 F-250 4x4 w/leaf springs in front (don't know if this matters). I think the axle is a D50, but I am not sure. How can I identify the axle as a D50 or a D44. I want to buy some manual hubs to replace the automatics, but don't want to order the wrong ones.This is just a simple video part of the ls Swap Jeep Ford 8.8 axle build showing what the axle tag means.The "3" represents the axle type, while the "L" indicates the presence of a limited slip differential. Example 2: B6. For this example, the axle code corresponds to a Ford truck with a 3.55 axle ratio and a non-limited slip differential. The "B" represents the axle type, and the absence of an "L" indicates a non-limited slip ...Axle Type. The following lists the available axle ratios and associated codes: 3A - 3.31 ratio 3B - 3.58 ratio 3C - 3.73 ratio Transmission Codes. Available transmissions are as follows: B - Mod Hybrid Transaxle (A10R80) - MHT T - 10-speed automatic (10R60) U - 10-speed automatic (10R80) Spring Codes. Spring codes are listed as a 2-part code.The rear axle has a readable plate: 4:10; D3TA-MA / Then: 663382411 whatever this is. Mish-mash Dana ID number. Ford ID number: D3TA-MA / Dana ID number: 603382-11 = Dana 60 / 4.10-1 / No Limited Slip. Front Axle: has a casting "44 6CF" from the numbers I have this is either a 3.54 or 4.09 ratio with locking hubs.Oct 20, 2003 · Ford Rear-Axle Quick Reference. It's easy to understand Ford rear-axle identification. Five basic types have been used in Fords, Mercurys, and Lincolns since 1957. In 1977.5 Ford's new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.The '05+ front has radius arm mounts case into the pumpkin, '99-'04 has leaf spring pearch. The '05+ front will have the 3 bolt, thin silver dialout hub with "FORD" turn knob, the '99-'04 will generally have the cheap black plastic dialout and turn knob. Rears are both 10.5" Sterlings for the SRW trucks. Don't know a quick way to ID them off ...

1928-1931 Model A axles have a uniform curve from end to end. The spring perch bosses are 2 1/4 inches. 1932 axles were the first Ford axles to be made with a slight drop. These axles are often referred to as 1932 heavy axles. They are unique among early Ford axles in having a wider recess at the ends, and a slightly raised area on the front and back of the spring perch bosses in the shape of ...409 = Print Number (Model Number) B = Revision Identifier (Change in Design) 3L73: 3L73 = 3.73 Ratio. L = Limited Slip. Absence of L = Open Differential. A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3 (space)73. 102 denotes the ring gear size. 10.25 inches.Clutch, Transmission, Differential, Axle & Transfer Case. 1. 09-08-2004 09:00 PM. /. 2004 - 2008 F150 - Axle identification - On my 04 lariat 4x4 the axle code is 26, which from my research says 3.73 non limited slip. Which a 4x4 with non LS is a sad thing. But when I spin the tires they both spin.Instagram:https://instagram. celina pompeani babymen tickled videoswa state hunting forumcrumbl cookies arlington va from elizabethtown kentucky. darnit. i guess there is a difference in spindle size. mine is so big the bearings wont fit. so now im looking for 47-53 1/2 ton spindles or a new axle. either or. shtterbug8, Mar 10, 2013. SHARE POST #8. dtlr downtown pittsburghblue pill with c 1 Originally Posted by bryyce62. Front axle is a monobeam Dana Super 60. Rear axle is a Ford Sterling full floating beam 10.5". As for the T-case, all I can find is that it's a 2 speed, part time unit. Pages 82 & 83 of the 2013 F-series order guide. Kind of hit it. Front axle is a standard d60 for f250 and 350.All Dana axles have a Bill of Materials (BOM) number stamped into the long axle tube that can be used to look up many of the axle's important details including the gear ratio, ring gear rotation, differential type and spline count, as … how long can i keep trimix in a syringe To help you find the right part, we first need to properly identify the axle you have or need. Not all vehicles are set up the same, even though they may be the same make and model. A Chevy 1/2 ton pick-up may have a Chevy 10 bolt rear axle or a 12 bolt rear axle. Both of these are semi-floating axles. A Chevy 3/4 ton pick-up may have a 14 bolt ...Vehicles. Take the route to proven performance with Spicer ® parts and Dana axle components for Ford ®. These genuine service parts are application-engineered specifically for Ford vehicles, and our rigorous standards assure dependability and durability. When it’s time to replace Ford drivetrain or axle components, get the highest-quality ...